IRM-8601V-1资料

MODEL NO:

Device Number:DMO-860-041 REV: 1.0

IRM-8601V-1ECN: Page: 2/10

■ NOTES：

1. This drawing measure is a standard value. All dimensions are in millimeter.

2. In case of designation is tolerance ±0.3mm.

3. Lead spacing is measured where the lead emerge from the package. 4. Protruded resin under flange 1.0mm Max. 5. Lens color: Black.

6. Above specification may be changed without notice. EVERLIGHT will reserve authority

on material change for above specification.

7. These specification sheets include materials protected under copyright of EVERLIGHT

corporation. Please don't reproduce or cause anyone to reproduce them withoutEVERLIGHT consent.

8. When using this produce, please observe the absolute maximum ratings and the

instructions for use outlined in these specification sheets. EVERLIGHT assumes noresponsibility for any damage resulting from use of the product which does not complywith the absolute maximum ratings and the instructions included in these specificationsheets.

EVERLIGHT ELECTRONICS CO., LTD.

MODEL NO:

Device Number:DMO-860-041 REV: 1.0

IRM-8601V-1ECN: Page: 3/10

■ Description：

IRM-8601V-1 are small and high performance receiving devices for infrared remote control

system. Regarding the transmission distance, IRM-8601V-1 is longer than IRM-8601S-1. The pulse width of IRM-8601V-1 are stable relating to commander's power or distancebetween transmitter and receiver.

■ Feature：

High protection ability to EMI and metal case can be customized.Mold type and metal case type to meet the design of front panel.Elliptic lens to improve the characteristic againstLine-up for various center carrier frequencies.Low voltage and low power consumption.High immunity against ambient light.Photodiode with integrated circuit.TTL and CMOS compatibility.Long reception distance.10. High sensitivity.1. 2. 3. 4. 5. 6. 7. 8. 9.

■ Application：

1. Optical switch

2. Light detecting portion of remote control

•AV instruments such as Audio, TV, VCR, CD, MD, etc.•Home appliances such as Air-conditioner, Fan , etc.•The other equipments with wireless remote control.•CATV set top boxes•Multi-media Equipment

EVERLIGHT ELECTRONICS CO., LTD.

MODEL NO:

Device Number:DMO-860-041 REV: 1.0

IRM-8601V-1ECN: Page: 4/10

■ Absolute maximum ratings： (Ta=25℃)

ParameterSymbolRatingsUnitNoticeSupply VoltageVcc0~6V

℃-30〜+85Operating TemperatureTopr

℃-40〜+85Storage TemperatureTstg

Soldering Temperature

Tsol

260

℃

4mm from mold body

less than 5 seconds

■ Electro Optical Characteristics： (Ta=25℃)

ParameterTYPMAXUnitConditionSymbolMIN

Vcc4.555.5VSupply VoltageDC voltageIcc--3mANo signal inputSupply Current

B.P.F Center

FrequencyPeak WavelengthTransmissionDistanceHalf Angle(Horizontal)Half Angle(Vertical)High Level Pulse

WidthLow Level Pulse

WidthHigh Level Output

VoltageLow Level Output

VoltagefoλpL0L45θhθvTHTLVHVL

--105--4004004.5-

32.75940--4535---0.2

-----800800-0.5

KHznmmdegdegµsµsVV

At the ray axis *2At the ray axis

*1

*1:The ray receiving surface at a vertex and relation to the ray axis in the

φ= 0° and φ=45°. range of

*2:A range from 30cm to the arrival distance. Average value of 50 pulses.

EVERLIGHT ELECTRONICS CO., LTD.

MODEL NO:

Device Number:DMO-860-041 REV: 1.0

IRM-8601V-1ECN: Page: 5/10

■ TEST METHOD：

The specified electro-optical characteristics is satisfied under the following Conditions at the controllable distance.

cMeasurement place

A place that is nothing of extreme light reflected in the room.

dExternal light

Project the light of ordinary white fluorescent lamps which are not high Frequency lamps and must be less then 10 Lux at the module surface. (Ee≦10Lux)

eStandard transmitter

A transmitter whose output is so adjusted as to Vo=400mVp-p and the output Wave form shown in Fig.-1.According to the measurement method shown in Fig.-2 the standard transmitter is specified.

However , the infrared photodiode to be used for the transmitter should be λp=940nm,∆λ=50nm. Also, photodiode is used of PD438B (VR=5V). (Standard light / Light source temperature 2856°K). fMeasuring system

According to the measuring system shown in Fig.-3

EVERLIGHT ELECTRONICS CO., LTD.

MODEL NO:

Device Number:DMO-860-041

IRM-8601V-1ECN:

REV:1.0

Page: 6/10

■ Block Diagram：■ Application Circuit：RC Filter should be connected closely between Vcc pin and GND pin.EVERLIGHT ELECTRONICS CO., LTD.

MODEL NO: Device Number:DMO-860-041 REV: 1.0IRM-8601V-1ECN: Page: 7/10 Fig.-1 Transmitter Wave FormCarrier frequency is adjusted to center frequency of each product.D.U.T output PulseIR TANSMITTER OUTPUT WAVE FORMOUTPUT PULSE OF DEVICEDuty=0.5 Fig.-2 Measuring Method20cm10k+5.0±0.1V10uFFig.-3 Measuring SystemL: Transmission DistanceVccOUTD.U.TGNDθθStandard Transmitter100kVoutStandard TransmitterVoutOscilloscopeθ: Angle Of Horizontal & Vertical DirectionEVERLIGHT ELECTRONICS CO., LTD.

MODEL NO:

Device Number:DMO-860-041 REV: 1.0

IRM-8601V-1ECN: Page: 8/10

■ TYPICAL ELECTRICAL/OPTICAL/CHARACTERISTICS CURVES Fig.-4 Relative Spectral Sensitivity vs. Wavelength Fig.-5 Relative Transmission Distance vs. Directionθ Fig.-6 Output Pulse Length vs. Arrival Distance Fig.-7 Arrival Distance vs. Supply Voltage Fig.-8 Relative Transmission Distance vs. Center Carrier Frequency Fig.-9 Arrival Distance vs. Ambient TemperatureEVERLIGHT ELECTRONICS CO., LTD.

MODEL NO:

Device Number:DMO-860-041 REV: 1.0

IRM-8601V-1ECN: Page: 9/10

■ Reliability test item and condition： The reliability of products shall be satisfied with items listed below. Confidence level: 90% LTPD: 10%Test ItemsOperation lifeTest ConditionsFailure JudgementCriteriaSamples(n)Defective(c) n=22,c=0 n=22,c=0Vcc=5V,Ta:25℃ 1000hrs 1 cycle -40℃ +25℃ +85℃L0≦ L×0.8Temperature (30min) 5min (30min)L45≦ L×0.8cycle 50 cycle test -10℃ to +100℃Thermal shock (5min) (10sec) (5min) 50 cycle testL: LowerHigh temperatureTemp: +85℃ 1000hrsspecification limitstorageLow temperatureTemp: -40℃ 1000hrsstorageHigh temperatureTa: 85℃ RH:85% 1000hrsHigh humidityTemp: 260±5℃ 5secSolder heat4mm Form the bottom of thepackage.Temp: 230±5℃ 5secMore than 90% ofSolderabilityLead to be covered4mm Form the bottom of theby solderingpackage. n=22,c=0 n=22,c=0 n=22,c=0 n=22,c=0 n=22,c=0 n=22,c=0EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number:DMO-860-041 REV: 1.0IRM-8601V-1ECN: Page: 10/10Packing Specifications1.Bag4.53.54.05.515±0.5Label19±0.522EVERLIGHTOpto-electronic,Compoments2.Box15Label3.Carton24 E CPN : Customer’s Production NumberVERLIG Label P/N : Production Number QTY : Packing Quantity CAT : Ranks 4 8 HUE : Peak Wavelength REF : ReferenceLabel UNIT ： cm LOT NO : Lot Number MADE IN TAIWAN : Production placePacking Quantity Specification 1. 250 Pcs/1Bag，6 Bags/1Box 2. 10 Boxes/1Carton33HT9